My Community

Videos of the 2gr Celica

https://rumble.com/v3syt8k-celica-eps-in-action.html

https://rumble.com/v3txlua-success-tach-works-now-2gr-swap-5gc.html
https://rumble.com/v2kt3x6-v6-swap-tach.html
https://rumble.com/v2kym6u-v6-swap-tach-pt2.html
https://rumble.com/v2kzv14-v6-swap-tach-mod-pt3.html
https://rumble.com/v2l06g6-v6-swap-tach-mod-pt4.html

Ran a 15.2 which is slow for the swap but 2.6 seconds faster than the previous time with the 5sfe.
The exhaust tubing was too small. It’s much happier now.
Excuse the fart can sound, the muffler sucked. In care it sounds amazing

https://rumble.com/v3wt5u2-first-run-of-the-day-2gr-celica.html

https://rumble.com/v3wt8d2-second-run-of-the-day-2gr-celica.html

https://rumble.com/v3t95ox-2gr-5th-gen-celica-in-car-audio-only.html



https://rumble.com/v47adsf-unboxing-2gr-celica-parts.html

https://rumble.com/v47br6r-second-part-of-the-frankenstein-motorworks-goodie-box.html

Final product once it’s bolted together.

For reference the locknuts should be on the main pivot shaft and the master cylinder pivot, there should be a light bit of slack so they can pivot freely. DO NOT OVER TIGHTEN!

neutral safety switch

Manual swap pedal box writeup.

This is the production manual clutch pedal swap parts list needed to complete this.


The parts kit is available here:
https://marketplace.sendcutsend.com/p/C239R269/svx-manual-swap-pedal-kit

Crossmember kit available here:
https://marketplace.sendcutsend.com/p/C757D217/subaru-svx-manual-transmission-swap-crossmember

Assembly video:
https://rumble.com/v6uoi89-subaru-svx-manual-swap-pedal-kit.html


Parts required:

-Wilwood master cylinder
Edit: my master cylinder was 0.75 which was paired with a 0.79 slave (push clutch, which I believe is an older setup?). Wrx gearboxes with a pull clutch have a 0.8125” slave and 0.69 master cylinder. The pedal ratio is pretty close.
Depending on which transmission and slave cylinder you should pick accordingly.

280-12384 0.625”,
280-12385 0.75”,
280-12386 0.8125”,
280-12387 0.875”,
280-12390 0.9375”,
280-12388 1”


-Neutral Safety Switch
Switch PN: 83281-AA000 (see picture added in a later reply)
Pigtail:
https://iwireusa.com/collections/all/products/cruise-clutch-switch-plug?_pos=2&_sid=26a93906f&_ss=r&variant=40734129979545
(Courtesy of Galen Helmgren)



Summit racing AN fittings and hose:

(A)   1x -4an to slave (m10-1.0)
SFL-SF35103
(Does not appear to include a copper seal washer, should be able to get an M10 washer at Oriellys)

(B)    1x 1/8 NPT 90* to -4an
FRA-582204

(C)    1x 3ft -4an hose
SUM-220986


Options:
Depending on where you have your pass through hole in the firewall you may want a different angle fitting off the slave cylinder (D) and depending how you want to run the line off the master cylinder (E), I wrapped around the front (closest to the driver) but some may choose other paths.
Options for both are below: straight, 45* or 90*

-4an hose end 90* -4an fitting
SUM-220146

-4an hose end 45* -4an fitting
SUM-220143

-4an hose end straight -4an fitting
SUM-220480



Hardware required:
1x M10-1.5x110mm bolt (flange type if possible, 12.9)- Main Pivot Bolt
McMaster-Carr PN: 98093A229 (pack of 10)

1x M10-1.5 lock flange nut - Main Pivot Nut
McMaster-Carr PN: 90426A130 (pack of 25)

1x M10-1.25 nut - Jam Nut for Neutral Safety Switch
McMaster-Carr PN: 93737A112 (pack of 25)

3x M8-1.25x25mm flange bolt - Bracket Mount and Master Cylinder Pivot
McMaster-Carr PN: 95735A425 (pack of 25)

2x M8-1.25x60mm flange bolt - Master Cylinder Mount Bolts
McMaster-Carr PN: 95735A461 (pack of 25)

4x m8 flange nuts - Master Cylinder Mount Nuts and Bracket Mount Nuts
McMaster-Carr PN: 90374A213 (pack of 50)

1x m8 flange lock nut - Master Cylinder Pivot Nut
McMaster-Carr PN: 90426A120 (pack of 50)

2x M5-0.8x16mm button/pan head - Pedal Pad Mount Bolts
McMaster-Carr PN: 98093A229 (pack of 10)

2x M5 flange nuts - Pedal Pad Mount Nuts
McMaster-Carr PN: 94920A300 (pack of 25)



-Volvo clutch return spring
Return Clutch Pedal Spring “Volvo Kenworth 22531 82332690 82332690” on eBay
Posted as “ VOLVO truck 82332690 8189666 1628381 22531”
https://www.ebay.com/itm/374639124485?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=8ajwfzc9q6o&sssrc=4429486&ssuid=r1wUsqcDR1e&var=&widget_ver=artemis&media=COPY




This requires drilling the side of the brake pedal mount, trimming the pedal pad down to wrx size
Also possibly drilling the hole for the pivot out slightly (bending with holes after laser cutting isn’t always exact, so a slight variance can be remedied with the index drill bit mentioned in the video)

You’ll need 1-2 holes in the firewall and a grommet for the slave and reservoir lines.

The adjustable master cylinder placement for different pedal ratios