My Community

Members => General Discussion => Topic started by: cuttyman9 on June 27, 2020, 04:12:19 PM

Title: TL Type S rear BBK
Post by: cuttyman9 on June 27, 2020, 04:12:19 PM
Acura TL Type S rear BBK

覧-calipers覧-
Ss camaro
Tesla model S (20.662.00 for left and right)
Ctsv v1 and v2
(Non hellcat) Srt8/srt challenger and charger (require a notch near the parking brake area to fit this kit)

覧-Rotors覧-
370z sport rear rotors (durago br900722)
https://www.rockauto.com/en/catalog/nissan,2015,370z,3.7l+v6,3310085,brake+&+wheel+hub,rotor,1896

覧Hardware-
4x M10-1.5 x 50mm  Hex head screws link below, confirm the specs before ordering
https://www.fastenal.com/products/details/11113836

4x M10-1.5 lock nuts link below, confirm the specs before ordering



4x M12-1.75 x 60mm socket cap screws link below, confirm the specs before ordering

https://www.fastenal.com/product/fasteners/sockets/socket-cap-screws/600040?categoryId=600040&level=3&aggregationSection=true&Dia%2FThread+Size=M12-1.75&Finish=Zinc&Grade=Class+12.9&Length=60mm&showAll=Dia%2FThread+Size&showAll=Length&selectedAggregation=Length


5mm spacers (may require longer studs)

Hub rings- 64.1 to 68.1 (Honda to Nissan)
You値l need to cut them down so it only touches the rotor.
(This is the save cost over spending ~100 for custom aluminum hub rings)

Title: Re: TL Type S rear BBK
Post by: cuttyman9 on September 11, 2020, 09:53:28 PM
Here are the installed pictures of the metal bracket.

One thing to note, the SRT calipers need slight clearancing near where the caliper bolts on to clear the parking brake backing plate.
The 5g camaro SS rears and Tesla model S rears have proven to have the notches needed (ctsv v1/v2 haven’t been checked yet.



Title: Re: TL Type S rear BBK
Post by: cuttyman9 on September 14, 2020, 05:03:48 PM
Pictures
Title: Re: TL Type S rear BBK
Post by: cuttyman9 on September 14, 2020, 05:07:31 PM
************************DISCLAIMER*********************
 
The person that is purchasing this product makes the following representations and acknowledges and agrees to the following terms and conditions:
 
This off-road race only product ("this Product") is designed and intended for use in organized, amateur and professional racing events, but is limited to closed-course racing and open-course racing that is formally sanctioned by a recognized racing organization involving the motor vehicle in which it is installed (the "Vehicle"). It is not for use on public highways or roads nor is it for recreational off-road use other than solely for competition purposes. The person or entity buying this Product and/or using this Product (the "User") agrees to use the Vehicle solely for competition uses as described herein.
 
The User accepting this disclaimer acknowledges and hereby indemnifies and saves harmless Overkill Engineering, its officers, employees, agents, distributors and dealers for any damages, penalties, fines, expenses or other costs which may arise from the use of this Product and without limiting the generality of the foregoing specifically acknowledges the following:
 
   Use of this Product for purposes other than solely for competition is a violation of federal law and may violate applicable state or local environmental, motor vehicle and other laws. The User warrants that this Product shall only be used in sanctioned closed-circuit events.
-That use of this Product may violate warranties from the manufacturer of the Vehicle or from others.
-That use of this Product may make the Vehicle unfit or unsafe for the purposes intended or for any purpose and cause personal injury, property damage or death.
-That the installation of this Product, improper installation of this Product, use of this Product with other components or failure to use this Product in conjunction with other components, could result in or cause personal injury, property damage or death.