TL Type S rear BBK

[cuttyman9]

Acura TL Type S rear BBK

覧-Calipers覧-
-2010-2015 Ss Camaro rear calipers
-2012-2020 Tesla model S rear calipers
-Maybe but not confirmed Ctsv v1(04-07)and v2(2008-13)
- Srt8/srt challenger and charger (require a notch near the parking brake area to fit this kit)
Hellcat/scat pack 4 pot rear are yet to be tested.
Confirm the calipers with these PN痴 (20.662.00 for left and right)

覧-Rotors覧-
370z sport rear rotors
https://www.rockauto.com/en/catalog/nissan,2015,370z,3.7l+v6,3310085,brake+&+wheel+hub,rotor,1896

覧Hardware�-
4x M10-1.5 x 50mm  Hex head screws� link below, confirm the specs before ordering
https://www.fastenal.com/products/details/11113836
**steel brackets: use 40mm long hardware**

4x M10-1.5 lock nuts � link below, confirm the specs before ordering

4x M12-1.75 x 60mm socket cap screws � link below, confirm the specs before ordering
**steel brackets: use 30mm long hardware instead**

覧勇xtras覧�

�5mm spacers (used between the rotor and hub to align the parking brake drum, otherwise it drags on the backing plate. A 3mm spacer could be used with a washer spacing the caliper toward the inside of the car, but it痴 a little on the tight side and use at your own risk)
https://www.amazon.com/Hubcentric-5x114-3-Spacers-Integra-Element/dp/B01M6239P8/ref=sr_1_3?keywords=5mm+spacer+64.1&qid=1686948075&sr=8-3

羊equires longer studs (arp part number 100-7712, 1 per side)

幽ub rings- 64.1 to 68.1 (Honda to Nissan)
You値l need to cut them down so it only touches the rotor.
(This is the save cost over spending ~100 for custom aluminum hub rings)

^Hub rings are used to center the Nissan rotor to the Honda hub, they will need to be cut down to sit flush with the rotor so that the wheel hub ring fits.


********Due to inconsistencies with Honda/Acura knuckle casting the brackets/knuckle may require some clearancing. The inconsistencies seem to be random and not specific to any year or type S vs non type S.*******

[cuttyman9]

Pictures thanks to Chris Cansler!
He was the first to install the rear kit.

The backing plate was removed, it痴 possible it can be trimmed and bent back but removing it insures you have plenty of room.

This shows the longer studs and the spacer used to offset the rotor to clear the parking brake drum.

You can see the increase in leverage with the larger diameter these rotors offer.

[cuttyman9]

Here are some pictures of them fully installed.
(Photos courtesy of Chris Cansler and Manuel Alcaraz)

The last picture is something that was brought up to me later.
It seems the control arm mount that runs diagonal that the bracket has a big notch to clear it varies quite heavily.
Between 3 we致e seen installed there痴 been one that clears fine, one that required a little clearancing of the stock knuckles casting flash and the other that took a good bit of clearancing so be aware that it might require a little bit of grinding until the knuckle casting is smooth if you池e one of the unlucky ones. It doesn稚 seem to matter if it痴 TL base or Type S, it痴 just casting variation on Honda痴 part.

[cuttyman9]

************************DISCLAIMER*********************
 
The person that is purchasing this product makes the following representations and acknowledges and agrees to the following terms and conditions:
 
This off-road race only product ("this Product") is designed and intended for use in organized, amateur and professional racing events, but is limited to closed-course racing and open-course racing that is formally sanctioned by a recognized racing organization involving the motor vehicle in which it is installed (the "Vehicle"). It is not for use on public highways or roads nor is it for recreational off-road use other than solely for competition purposes. The person or entity buying this Product and/or using this Product (the "User") agrees to use the Vehicle solely for competition uses as described herein.
 
The User accepting this disclaimer acknowledges and hereby indemnifies and saves harmless Overkill Engineering, its officers, employees, agents, distributors and dealers for any damages, penalties, fines, expenses or other costs which may arise from the use of this Product and without limiting the generality of the foregoing specifically acknowledges the following:
 
   Use of this Product for purposes other than solely for competition is a violation of federal law and may violate applicable state or local environmental, motor vehicle and other laws. The User warrants that this Product shall only be used in sanctioned closed-circuit events.
-That use of this Product may violate warranties from the manufacturer of the Vehicle or from others.
-That use of this Product may make the Vehicle unfit or unsafe for the purposes intended or for any purpose and cause personal injury, property damage or death.
-That the installation of this Product, improper installation of this Product, use of this Product with other components or failure to use this Product in conjunction with other components, could result in or cause personal injury, property damage or death.

[cuttyman9]

**********Steel brackets!!************

This is an update for a new cheaper 2 pc design for brackets!

These below are for attaching the two pieces of bracket to each other:

6x M10-1.25x25mm
6x 2.5mm thick washers (McMastercarr PN 96505A117)

It also requires a washer between the one bracket and the knuckle.
4x m10 washers (McMastercarr PN  98035A106)

[cuttyman9]

Picture of the orientation of the bracket pieces.